Large capacity autoclaves experience various problems because of wear and tear combined with misuse and insufficient maintenance. This section reveals the primary issues encountered by users.
The sterilization failure in large capacity autoclaves results from incorrect cycle settings combined with overloading and insufficient steam penetration.
Maintain effectiveness of your autoclave by using appropriate loading methods and confirming cycle settings while performing regular chamber cleanings.
Steam leaks occur because of damaged door seals or doors that are not closed properly.
Perform routine inspections of seals and replace any gaskets that show signs of wear.
The source of pressure build-up issues stems from broken pressure valves and obstructed steam vents.
Check pressure valves to ensure they function correctly while cleaning the steam vents.
원인: Faulty sensors or inadequate calibration.
Regular calibration of the autoclave and replacement of its damaged sensors will solve the issue.
원인: Electrical or software malfunction.
Check the user manual to identify specific error codes or reach out to technical support for assistance.
대용량 오토클레이브에 대한 자세한 내용은 다음을 참조하세요. 그리고 .
The longevity of your autoclave depends on proper maintenance which ensures its consistent performance. Follow these tips:
Clean out any remaining residue and particles from the chamber after each operation.
Apply cleaning agents that are approved to protect the stainless steel interior from damage.
Regular inspections of door seals must include checks for any cracks or signs of wear.
It’s necessary to replace seals when they show signs of wear to avoid steam leaks.
Distilled or demineralized water will help prevent both scaling and corrosion in your machine.
Regular cleaning of the water reservoir is essential for preventing contamination.
Ensure accurate temperature and pressure readings by calibrating devices every 6 to 12 months.
Use professional calibration services for best results.
Perform regular inspections of pressure release valves and steam vents to detect any blockages or damage.
Ensure safety and efficiency by cleaning these parts on a regular basis.
Lubricate hinges, locks and all moving parts to prevent wear.
Regular biological testing should be done to confirm that sterilization processes work effectively.
Perform spore tests to verify that the autoclave operates according to industry requirements.
Addressing problems quickly through troubleshooting helps avoid operational stoppages and expensive repairs. The following information provides solutions to typical problems.
Steps to Resolve:
Verify loading methods to achieve adequate steam distribution.
Verify cycle settings and adjust if necessary.
Clean the chamber and remove debris.
Steps to Resolve:
Check door seals for any damage and perform replacements when necessary.
Do not start the cycle until you have confirmed that the door is fully closed.
Steps to Resolve:
Clean steam vents to remove blockages.
Examine the pressure valves to verify their working condition and substitute components that exhibit damage.
Steps to Resolve:
Perform calibration procedures on the autoclave to maintain precise temperature measurements.
Replace faulty sensors with new ones.
Steps to Resolve:
The user manual contains information about specific error codes.
To eliminate non-critical software errors, perform an autoclave restart.
Contact technical support for complex issues.
Regular maintenance and prompt troubleshooting are essential for ensuring the longevity and efficiency of large capacity autoclaves. By addressing common issues, performing routine inspections, and following best practices, you can minimize downtime and extend the lifespan of your equipment.
Whether you’re using a 200-liter or 300-liter autoclave, understanding its maintenance requirements and troubleshooting solutions will help you achieve consistent sterilization results.
If you’re in need of reliable autoclave solutions or technical support, contact 켈링 메디컬 오늘.
It’s recommended to clean the chamber daily after each use to prevent residue buildup.
Use distilled or demineralized water to prevent scaling and corrosion.
Inspect door seals regularly and replace them if they show signs of wear or damage.
Refer to the user manual for guidance or contact technical support for assistance.
Calibration is recommended every 6–12 months to ensure accurate temperature and pressure settings.
For more information about maintaining and troubleshooting large capacity autoclaves, reach out to 켈링 메디컬 오늘:
이메일:
WhatsApp:
웹사이트:
오토클레이브 공정은 의료, 실험실 및 연구 시설에서 효과적인 멸균을 통해 유리 제품과 기구를 보호하기 위해 사용하는 필수 멸균 방식입니다. 고압 증기는 이 과정에서 병원균을 제거합니다.
오토클레이브 공정은 의료, 실험실 및 연구 시설에서 효과적인 멸균을 통해 유리 제품과 기구를 보호하기 위해 사용하는 필수 멸균 방식입니다. 고압 증기는 이 과정에서 병원균을 제거합니다.
