네일 살롱에서 오토클레이브를 올바르게 사용하는 방법

오토클레이브

Nail salons must ensure proper sterilization practices to maintain hygiene and protect their clients. Nail tools touch skin directly which makes them susceptible to contamination when sterilization procedures are not properly followed. An autoclave stands as the superior sterilization method because it completely destroys all microorganisms such as bacteria, viruses, fungi, and spores.

The ownership of an autoclave requires proper knowledge of its operation. Using an autoclave incorrectly will jeopardize the sterilization process and endanger your clients’ health. This article features a detailed guide for autoclave use in nail salons while identifying common errors to steer clear from and essential maintenance advice to ensure your autoclave operates at peak performance.

Step-by-Step Guide to Using an Autoclave

Following the correct procedures when using an autoclave ensures the highest level of sterilization. Here’s a detailed guide:

1. Preparing Nail Tools for Sterilization

You need to properly prepare your tools prior to placing them into the autoclave.

Wash the tools using soap and water until all visible dirt, debris, and organic matter has been removed. Autoclaves need pre-cleaned tools because they are unable to sterilize any that still contain dirt or organic matter.
Make sure that every tool has dried completely prior to putting them into the autoclave. Sterilization effectiveness can be reduced by the presence of excess moisture on tools.
Tools must be stored inside sterilization pouches or trays. Confirm successful sterilization using sterilization pouches equipped with indicator strips.

2. Loading the Autoclave Correctly

Tools loaded correctly into the autoclave allow steam to circulate freely and reach every surface of the tools.

Maintain sufficient space between tools to avoid overcrowding the autoclave chamber. Ensure items have adequate spacing to enable steam penetration through all surfaces.
Position sterilization pouches so that the paper side is on top while the plastic side remains at the bottom.
Loading too much into the chamber obstructs steam circulation which leads to sterilization failure.

3. Setting the Appropriate Cycle

Effective sterilization depends on choosing the right autoclave cycle.

Autoclaves commonly function at either 121°C (250°F) or 134°C (273°F) while maintaining suitable pressure levels. You should read your autoclave manual to find specific operating instructions.
The sterilization cycle duration varies depending on the type of tools which are being sterilized. The standard sterilization time for metal tools using 121°C heat ranges between 15 and 20 minutes.
Begin the sterilization cycle after adjusting the settings and wait for the autoclave to finish the process.

4. Removing and Storing Sterilized Tools

Tools must remain in the chamber after the cycle ends to cool down before removal. The tools should cool within the chamber to avoid contamination risks.
Make sure the color of the indicator strips on the pouches shows successful sterilization.
To keep sterilized tools sterile until they are needed store them in a clean and dry storage area.

피해야 할 일반적인 실수

The best autoclave will fail to sterilize if it is not used correctly. Avoid these common mistakes:

1. Overloading the Chamber

When the chamber gets overloaded, steam circulation becomes faulty and results in incomplete sterilization. It is essential to adhere to the manufacturer’s specified load capacity to ensure proper sterilization.

2. Skipping the Cleaning Step

If you don’t clean tools prior to sterilization the autoclave won’t function properly. Microorganisms remain protected from sterilization when dirt and debris cover them.

3. Using Improper Settings

Incorrect temperature, pressure, or cycle time settings during autoclave operation lead to sterilization failures. Verify your autoclave settings before beginning each sterilization cycle.

4. Neglecting Maintenance

Inadequate maintenance can cause an autoclave to operate incorrectly. Consistent performance requires regular maintenance of your equipment.

Maintenance Tips for Your Autoclave

Maintaining your autoclave properly will prolong its operational life and guarantee dependable sterilization results. Here’s what you should do:

일일 유지 관리

Use a soft cloth to wipe down the chamber and eliminate any residue.
Clear the Water Reservoir by releasing all water and filling it back up with clean distilled water.

주간 유지 관리

Examine door seals and gaskets for signs of deterioration and wear. Replace them if necessary.
Take out the trays and clean them to stop accumulation.

월간 유지 관리

Apply a descaling solution to eliminate mineral buildup from the autoclave chamber and water lines.
Conduct a biological indicator test to confirm that the autoclave operates effectively.

전문 서비스

Make sure your autoclave stays in perfect working order by having a certified technician perform regular maintenance checks.

결론

Your nail salon must operate with a fully functional autoclave to protect your clients and uphold your business’s reputation. You will obtain consistent and effective sterilization results when you adhere to proper procedures while avoiding common errors and performing routine maintenance.

For high-quality autoclaves and expert guidance, contact 켈링 메디컬. We offer a wide range of sterilization solutions tailored to your needs.

이메일: inquiry@shkeling.com
WhatsApp: +8618221822482
웹사이트: https://autoclaveequipment.com/

For more information on sterilization methods, check out our next article: Autoclave Sterilizers vs. Other Sterilization Methods for Nail Salons.

자주 묻는 질문

1. Why is it important to clean tools before sterilization?

Cleaning removes dirt, debris, and organic matter that can interfere with the sterilization process. An autoclave cannot effectively sterilize tools that are not properly cleaned.

2. How often should I maintain my autoclave?

Perform daily, weekly, and monthly maintenance tasks as outlined in this article. Regular professional servicing is also recommended.

3. Can I sterilize all types of nail tools in an autoclave?

대부분의 금속 도구는 오토클레이브에서 멸균할 수 있습니다. 하지만 플라스틱이나 기타 열에 민감한 재질로 만들어진 도구는 적합하지 않을 수 있습니다. 항상 제조업체의 지침을 확인하세요.

4. What happens if I overload the autoclave?

Overloading prevents steam from circulating properly, resulting in incomplete sterilization. Always follow the manufacturer’s recommendations for load capacity.